Tokyomods Less Tension Throttle Spring

[grunt58]

Anyone use one? More specifically anyone use one on a TRX 450r? Any install tutorials?

Scroll down a little: http://www.tokyomods...7%20TRX450.html

My thumb gets fatigued very quickly. Never had this problem on my 400ex or any other quad.

 

[mx333]

I just cut the stock spring. You can also try a trx 90 lever as well they are slightly longer.

 

[Deven]

Yes I use one and I wouldn't use anything else. They work and work well

 

[airmobile101]

I just cut the stock spring. You can also try a trx 90 lever as well they are slightly longer.

Just make sure you use the 04/05 450r throttle. I think it works on the 400ex throttle also.

 

[El Mamito USMC]

I had a ligth spring put on my by Sredrum when he did my carb, not sure the brand, but ilove it

 

[TRXFLYER]

I use it on all three of mine, wouldn't be able to ride without them!

 

[grunt58]

Went ahead and bought it, figure for $30 it was worth a try. Not saying a spring is worth $30, price is ridiculously high for what it is.

Any tutorials on installing it? I found this for relocating the spring mount pretty much the same process I'd assume minus the drilling.

http://www.trx450r.org/forum/118-engine-tech-faq/155461-fcr-throttle-spring-mod.html

 

[grunt58]

So got the spring, pulled the carb, installed the spring went to tighten up the "Flat CR" cap and the casting broke. I think the cap was cocked and when I snugged it up it snapped. I blame myself wasn't being careful just wanted to get it done. This $30 job just got expensive. I don't think I have any other choice but to get a used carb. Unless someone has a great solution....?

With that said anyone selling a 08 450er carb or know a good place to get a used one? Found a few on ebay but they are a little high.

View attachment 621

 

[Deven]

Believe it or not, there are people who have spare carb bodies do to ripping the center gasket.

If not I have a complete fcr with Tokyo throttle spring

 

[grunt58]

Spare body would require rebuilding the carb which I can not do. I might have a guy to do it though.

How much for the spare?

 

[hoser]

Looks like you can buy that piece with the gasket for about $25.

 

[grunt58]

Thanks but I need the housing not the cap.

 

[Burke]

Do you want to sell your carb?... I'd like too try to fix it

 

[bigcountrydude]

personaly? i'd grind off the rest of where the threads are, aluminum weld a piece there and drill and tap it. just has to hold that little cover on.

 

[grunt58]

I think there is enough meat left to use a nut. Might jb weld the pieces back together along with the nut should be good enough. The sealing area is fine and intact.

 

[hoser]

Thanks but I need the housing not the cap.

Oh sorry, I must of read your post too quickly. Hopefully you find something.

 

[grunt58]

Got the cap fixed and have it put backed together. But to start it and have it stay idling I have to push on the thumb throttle just a bit. I think one of the sensors is being triggered or not being triggered. I just need to push it till it clicks up at the thumb throttle and it starts and idle as normal. If I let off the throttle it basically cuts out as opposed to stalling. Any thoughts on what to adjust?

08 450er

Thanks

 

[450Riot]

Do you have proper free play in the throttle cable? Should be able to feel a little slack in the cable. That however would be kinda backwards from your problem but you never know.

That or the hotstart cable got messed up and it's pulling when it shouldn't be?

How about the pilot screw? Can you tune it out with that?

Also the simple - no cracks in the boots or exhaust leaks?

 

[bigcountrydude]

its the TPS. your throttle cable is set to tight.