alanbmx Posted June 9, 2012 Posted June 9, 2012 here are the steps I did to remove and install my new extended axle 1. I loosened the large nut first with a big cresent wrench. Standing at the back of the quad turn the wrench down. sometimes these are tight as fuck, might need a little heat or a cheater bar. Mine was easy but most are a bitch http://www.offtopic.forum/uploads/imported/2012/06/axleinstallation002-1.jpg 2. then loosened the smaller nut until I could see the clip on the axle, had to tap the whole nut assembly in toward the swingarm to expose the clip, then popped the clip off with a screwdriver http://www.offtopic.forum/uploads/imported/2012/06/axleinstallation003-1.jpg at this point i jacked the quad up in the air, the front of the quad needs to be supported because when you remove the axle the balance point changes and the quad wants to tip forward, I used a jack stand http://www.offtopic.forum/uploads/imported/2012/06/axleinstallation013-1.jpg 3.removed the brake caliper. this bolt did not do it had to remove the 2 bolts below this one to get the caliper assy out of the way http://www.offtopic.forum/uploads/imported/2012/06/axleinstallation005-1.jpg 4. slide the disk off http://www.offtopic.forum/uploads/imported/2012/06/axleinstallation009-1.jpg 5. loosen the chain tensioner, and remove the rear sprocket http://www.offtopic.forum/uploads/imported/2012/06/axleinstallation008-1.jpg 6. slide the axle out http://www.offtopic.forum/uploads/imported/2012/06/axleinstallation010-1.jpg 7. I cleaned the old grease out with a rag, at this point I probably should have taken the carrier out and cleaned, lubed and reinstalled it but I did not. I put new grease inside the bearing and on the seals and greased the new axle http://www.offtopic.forum/uploads/imported/2012/06/axleinstallation011-1.jpg http://www.offtopic.forum/uploads/imported/2012/06/axleinstallation012-1.jpg http://www.offtopic.forum/uploads/imported/2012/06/axleinstallation014-1.jpg 3 Quote http://450rhq.com/data/MetaMirrorCache/92ac89484251c63d73340458b54ac18b.jpg By alanbmx at 2012-04-16
alanbmx Posted June 9, 2012 Author Posted June 9, 2012 8. side the axle in, the sprocket hub goes into the seal so it needs to be lubed, and you might have to tap it in with a deadblow hammer to seat it into the seal http://www.offtopic.forum/uploads/imported/2012/06/axleinstallation016-1.jpg http://www.offtopic.forum/uploads/imported/2012/06/axleinstallation017-1.jpg 9. lube the inside of the brake hub make sure you did not lose the o-ring that goes inside, lube the o-ring, lube the outside where it slides into the swingarm seal, and slide it in http://www.offtopic.forum/uploads/imported/2012/06/axleinstallation020-1.jpg o-ring http://www.offtopic.forum/uploads/imported/2012/06/axleinstallation018-1.jpg http://www.offtopic.forum/uploads/imported/2012/06/axleinstallation021-1.jpg 10. re install the stock retaining nut or a aftermarket one like the dura-blue one I bought, put antisieze on the threads of aftermarket ones since they are steel and aluminum, anytime steel threads go into aluminum use anti sieze http://www.offtopic.forum/uploads/imported/2012/06/axleinstallation022-1.jpg 11. reinstall the clip and tighten to torque specs, here is where the trouble starts for me, dura blue says at least 1/2" threads inside nut when tight, not gonna work I am going to have to fab a washer next week at work, sometimes aftermarket stuff needs a little extra to work right, says on thier web site to fab a washer, don't know why they do not make it right cannot be that much varation in bikes, anyway here is waht it looks like http://www.offtopic.forum/uploads/imported/2012/06/axleinstallation027-1.jpg http://www.offtopic.forum/uploads/imported/2012/06/axleinstallation028-1.jpg Good luck. And thanks to Todd at Immortal for the deal on the Tusk axle and the durablue nut that needs help:thumb: 1 Quote http://450rhq.com/data/MetaMirrorCache/92ac89484251c63d73340458b54ac18b.jpg By alanbmx at 2012-04-16
DPCones Posted June 10, 2012 Posted June 10, 2012 Good write up/pics. Quote http://450rhq.com/data/MetaMirrorCache/508e07386c71becab2bf881014f51ad6.jpg
hoser Posted June 10, 2012 Posted June 10, 2012 Thanks for taking the time to do the how-to! Should help a lot of guys that have trouble with removing the rear axle, and hopefully helps people understand which way to turn the nuts to loosen them! Quote
alanbmx Posted June 10, 2012 Author Posted June 10, 2012 Since I have to fab up a washer at work next week I decided to remove the carrier and clean it up. Probably a good idea since the O-rings were falling apart and it had some dirt and sand in it, and as I have read next to no grease, so now I am heading over to Motoworld here in Elcajon to see if they are open on Sundays and see if they have the o-rings in stock. :gr_driving3: trashed O-rings http://www.offtopic.forum/uploads/imported/2012/06/axleremoval002-1.jpg All cleaned up http://www.offtopic.forum/uploads/imported/2012/06/axleremoval003-1.jpg http://www.offtopic.forum/uploads/imported/2012/06/axleremoval001-1.jpg 1 Quote http://450rhq.com/data/MetaMirrorCache/92ac89484251c63d73340458b54ac18b.jpg By alanbmx at 2012-04-16
foretrax Posted June 11, 2012 Posted June 11, 2012 Awesome post for those that haven't done this before I know I spent an hour trying to figure out why the nuts wouldn't cone off the first time I took apart the axle ha ha oops Quote http://450rhq.com/data/MetaMirrorCache/b455c23f27ab6660d9fb8f1ddca3a9ba.jpg Sponsors GoPro SteelMX HookIt
450Riot Posted June 11, 2012 Posted June 11, 2012 What do you guys use to hold the axle? I've been taking the wheel off and grabbing the hub but now they are powdered and I don't really wanna touch em next time. Quote 2004 Honda Trx450Riot Kicker Dasa K&N Motul Kenda Pro Taper Motion Pro Streamline Blingstar
alanbmx Posted June 11, 2012 Author Posted June 11, 2012 What do you guys use to hold the axle? I've been taking the wheel off and grabbing the hub but now they are powdered and I don't really wanna touch em next time. Have someone step on the rear brake Quote http://450rhq.com/data/MetaMirrorCache/92ac89484251c63d73340458b54ac18b.jpg By alanbmx at 2012-04-16
Scandall519 Posted June 12, 2012 Posted June 12, 2012 My axle nut was a PITA to remove... but here is how I did it... 2 pipe wrenches and 2 cheater bars... [ATTACH]535.vB[/ATTACH] Quote [broken External Image]:https://fbcdn-sphotos-a.akamaihd.net/hphotos-ak-ash3/535191_10150850695242658_578822657_11641888_937094153_n.jpg
jasaus Posted December 10, 2012 Posted December 10, 2012 just like people like me looking for a cresent wrench at the last minute one needs to open up over 1 3/4 in. and the other needs to open up over 2 1/4 in. so you dont have to buy the wrong one like i did. i didnt take the time to measure the nut before i left the house.. might help Quote
El Mamito USMC Posted December 10, 2012 Posted December 10, 2012 thanks for the post. very useful and with pics.. Quote http://www.offtopic.forum/data/MetaMirrorCache/06f1a7ba567102d307e3f721efc437ad.jpg Zorros racing.. #123A - Baja 500, 2014 FINISHER !!! Subscribe to us on FB http://www.facebook.com/zorros.rt http://www.offtopic.forum/data/MetaMirrorCache/91c75944b97d47249f183869c9875a9e.gif http://www.offtopic.forum/data/MetaMirrorCache/5639c3ecf3b34b1f1e26b660950f9785.gif Join the http://www.Marines.com travel to exotic lands, meet exciting unusual people and kill them..
bvet4dog Posted December 22, 2012 Posted December 22, 2012 Well, i just finished installing my shocks! Now I'm in the middle of installing my axle / carrier. I just realized i do not have any dust seal or orings.... yikes! I stopped the installation process to ask some questions here. The rear caliper stay needs an o ring that's for sure, also i'll need a new seal bearing holder. The new lsr carrier did not come with a dust seal or extra o rings. Do i need one? From looking at my pics, it seems water, dust, dirt, sand could get into the carrier and fuck it up. Or is it the dust seal already built in into the carrier and the big bolt/nut and brake disc bolt go in snug to keep dirt out? What seals / dust seal / orings do i need!? (i want everything redone right) So looking at the swingarm schematic on RMATV... is item number 32, the right one for inside the caliper stay? Do i need item #36? I think that's all i'm seeing. Any advices/inputs would be appreciated. Thank you! Sorry for lots of questions haha, just want to do it right first time around. Quote 07 trx450r http://450rhq.com/data/MetaMirrorCache/cd3b5c0a9ec786930d0a92290fd034b5.jpg
bvet4dog Posted December 22, 2012 Posted December 22, 2012 http://www.offtopic.forum/uploads/imported/2012/12/20121221185907_zps21f05aae-1.jpg http://www.offtopic.forum/uploads/imported/2012/12/20121221185922_zps119e013d-1.jpg Quote 07 trx450r http://450rhq.com/data/MetaMirrorCache/cd3b5c0a9ec786930d0a92290fd034b5.jpg
bvet4dog Posted December 22, 2012 Posted December 22, 2012 here's a better pic http://www.offtopic.forum/uploads/imported/2012/12/20121222000447_zps5bb8ffdb-1.jpg Quote 07 trx450r http://450rhq.com/data/MetaMirrorCache/cd3b5c0a9ec786930d0a92290fd034b5.jpg
alanbmx Posted December 24, 2012 Author Posted December 24, 2012 when I did mine i got item 32, 2 of item 33, and item 36, had to order them and it took a couple of days, item 32 was the most dificult to figure out how it went, the oring seemed too big but i got it to work Quote http://450rhq.com/data/MetaMirrorCache/92ac89484251c63d73340458b54ac18b.jpg By alanbmx at 2012-04-16
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.